E-flite Blade mSR BNF Instrukcja Obsługi Pobierz pdf (Strona 9)

16 17

Transmitter-Specific Binding Instructions

DX5e:

A. Make sure the flight battery is disconnected from the 5-in-1 unit and the

transmitter is turned off.

B. Move the sticks and switches on the transmitter to the desired failsafe positions

(low throttle and neutral control positions).

C. Plug the flight battery into the receiver/5-in-1 unit. After 5 seconds the LED on the

5-in1 unit will begin flashing.

D. Pull and hold the Trainer Switch on the transmitter while turning the transmitter

on. Release the trainer switch once the LEDs on the front of the transmitter flash.

E. The LED on the receiver/5-in-1 unit will go solid and the system will connect after

several seconds.

F. If you entered bind mode correctly, you will see a solid LED approximately 5–10

seconds later on the receiver/5-in-1. You should now be bound to the transmitter,

and have full control and function.

DX6i:

A. Make sure the flight battery is disconnected from the 5-in-1 unit and the

transmitter is turned off.

B. Move the sticks and switches on the transmitter to the desired failsafe positions

(low throttle and neutral control positions).

C. Plug the flight battery into the receiver/5-in-1 unit. After 5 seconds the LED on the

5-in1 unit will begin flashing.

D. Pull and hold the Trainer Switch on the transmitter while turning the transmitter

on. Release the trainer switch once the word BIND flashes on the LCD screen on

the front of the transmitter.

E. The LED on the receiver/5-in-1 unit will go solid and the system will connect after

several seconds.

F. If you entered bind mode correctly, you will see a solid LED approximately 5–10

seconds later on the receiver/5-in-1. You should now be bound to the transmitter,

and have full control and function.

DX7 (includes DX7se):

A. Make sure the flight battery is disconnected from the 5-in-1 unit and the

transmitter is turned off.

B. Move the sticks and switches on the transmitter to the desired failsafe positions

(low throttle and neutral control positions).

C. Plug the flight battery into the receiver/5-in-1 unit. After 5 seconds the LED on the

5-in1 unit will begin flashing.

D. Press the bind button on the back of the transmitter while turning the transmitter

on. The bind button on the back of the transmitter will flash. Release the button

after 2–3 seconds.

E. The LED on the receiver/5-in-1 unit will go solid and the system will connect after

several seconds.

F. If you entered bind mode correctly, you will see a solid LED approximately 5–10

seconds later on the receiver/5-in-1. You should now be bound to the transmitter,

and have full control and function.

X9303:

A. Make sure the flight battery is disconnected from the 5-in-1 unit and the

transmitter is turned off.

B. Move the sticks and switches on the transmitter to the desired failsafe positions

(low throttle and neutral control positions).

C. Plug the flight battery into the receiver/5-in-1 unit. After 5 seconds the LED on the

5-in1 unit will begin flashing.

D. Press the bind button on the back of the transmitter while turning the transmitter

on. The bind button on the back of the transmitter will flash. Release the button

after 2–3 seconds.

E. The LED on the receiver/5-in-1 unit will go solid and the system will connect after

several seconds.

F. If you entered bind mode correctly, you will see a solid LED approximately 5–10

seconds later on the receiver/5-in-1. You should now be bound to the transmitter,

and have full control and function.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 25 26

Komentarze do niniejszej Instrukcji

Brak uwag

E-flite Blade mSR BNF Instrukcja Obsługi Strona 9

Komentarze do niniejszej Instrukcji